How do i hook up subs to a stock deck. Adding RCAs to a Standard Car Head Unit: 6 Steps (with Pictures)

How do i hook up subs to a stock deck Rating: 8,8/10 1488 reviews

Connecting Your Car Speakers to an Amp: Use Your Factory Wiring

how do i hook up subs to a stock deck

Start from the battery and pass on to the amplifier. Twist the amp remote wire blue to the cd player remote wire and wrap electrical tape around them so they are not shown. Source - factory unit connected to scosche hi low converter. I initially thought that behind the glove box would be the best place but i ended up cable tying it to a heater pipe that runs down the centre console. At the back of your stereo there is most likely one big plug which incorporates all of the inputs and outputs to and from your head unit.

Next

Can i hook up an aftermarket Sub to my stock Bose Amp?

how do i hook up subs to a stock deck

Then you connect the amp's outputs to the speaker wires of the vehicle harness via a 9-conductor speaker cable. Trying to push 140 watts through factory wiring may result in some power loss but shouldn't introduce distortion. Be sure to secure the speaker boxes to your vehicle. I left the two factory front speaker wires from the head unit connected also and have those connected to the tweeter only. If my speakers are 4ohm and I add 4ohm tweeters by tapping into the main speakers, will my amp see that channel as 2ohm? Or you could buy a and leave the sub channel unconnected until you get a subwoofer.

Next

Can i hook up an aftermarket Sub to my stock Bose Amp?

how do i hook up subs to a stock deck

Again your advice is greatly appreciated. I have my install kit on order and I'll be attempting to run the wires this weekend. I want to know if this setup will work and if it will be good or not. I don't think your reading at 1000 Hz will be very accurate, so don't depend on that for setting gain. The wires would run from one black connector to the other the right side of the photo below. But without knowing precisely what speakers, amp, and subs you're referring to, we can't really help you with advice.

Next

3 Ways to Wire an Amp to a Sub and Head Unit

how do i hook up subs to a stock deck

I've never had a stock radio before and with all the things that this one controls, it doesn't seem like swapping it out is going to be a real option. Use the tone controls of your receiver for that. A fried amp has more like a sizzling noise. Genocydal, depending on how powerful your aftermarket amplifier is, allong with tapping off the 3 factory wires, you'll need to run atleast 8awg power and ground wires with an inline fuse. You're a butcher who knows absolutely nothing about electricity's laws or how it works.

Next

Sub& Wiring To Stock Deck

how do i hook up subs to a stock deck

Maybe looking at the photo and its captions will help you visualize how this saves running speaker wire throughout the car to each speaker. . You can control the sub from the receiver but you lose its front-to-rear fade feature. To save time and space a popular solution is a powered subwoofer. Factory speaker wires are very thin, with high electrical resistance, so they can cause noticeable power loss when higher wattages try to get through.

Next

How to Hook Up a Subwoofer System to a Car's Stock Stereo

how do i hook up subs to a stock deck

In this setup it doesn't matter where the amp gets its signal, direct from the receiver or daisy-chained from another amp. I have used new speaker wires 16awg for tweeters and have used the existing factory wires for the component woofers! Then pull it out from the bottom of the dash column. However, you will not notice the noise through the subwoofers becuase the distortion is emitting at a higher freq. Just to get the jist of how to do it Steps on how to install subwoofers and amp into a car with a factory radio head unit. I would like to fix this by adding an amp but im not sure how to wire it in.

Next

Connecting Your Car Speakers to an Amp: Use Your Factory Wiring

how do i hook up subs to a stock deck

I try and sell audio equipement and I would probably do a lot better if I could expand my knowlege. After this is done, run the remote wire through the dashboard and the door jam. And I thought I was bad with car audio. My question is do I need to run new thicker gauge speaker wire or will I be fine with the factory wires? I would think if I discarded to wires coming out of receiver and taped them off and instead wired this loom to the harness it would only work if amp is on. Ive chatted to loads of people and its been suggested that its a major grouding issue. After hooking it everything, the amp turned on but the subs refused to omit any sound.

Next

How do you hook up subwoofers to an stock radio?

how do i hook up subs to a stock deck

I need to do some serious learning in both car and home audio systems. Two sub input rca on the amplifier. I have a 2001 Bonneville that I purchased 4 months ago. I am ordering a 5 channel amp soon to step my game up and I am trying to figure out how to wire it correctly! A little advice stay away from wal-mart equitment very poor quality and don't go near anything that says road gear or road master or even durabrand. So out came the metal file and i removed all the paint around the grouding point.

Next

Can you hook up subs to a stock cd player unit??

how do i hook up subs to a stock deck

Of course, you'll just most likely need a speaker level converter and splice into the rear speaker wires to provide signal for the amp. I have watched many videos and read many articles on how to wire a 5 channel amp but still have confusion with two things. My question is how many channels would I need on the processor as well as the amp? I have the power wire ran through the firewall to the battery and started running under the carpet on the drivers side. Is it simply disconnected from each speaker and taped up, in case of refitment of stock equipment later on, thus leaving it intact on the receivers harness. Any issues with just taping them off other than the usual warnings of tape potentially falling off or just capping them? The front door speakers work fine and the dash speakers work fine. I am using 2 channels to power 4 speakers. This wire is located at the back of the stereo deck.

Next