How do i hook up subs to a stock radio. Adding RCAs to a Standard Car Head Unit: 6 Steps (with Pictures)

How do i hook up subs to a stock radio Rating: 7,7/10 1546 reviews

How to Install a Powered Subwoofer

how do i hook up subs to a stock radio

Seeing as you bought your amp from Crutchfield, you should call Tech Support for free help setting up your system. Mids and Highs powered by Infonity Kappa Five 5channel amp. Thanks in advance if you can help Frank. As i say its not really influencing the signal to the rear speakers, i doubt it makes any difference you could detect with your ears even at high volume. Keep in mind that if you bought your gear from Crutchfield, you can call Tech Support for free help troubleshooting your system.


Next

How do you add an amp to stock silverado stereo?

how do i hook up subs to a stock radio

For ground, use a suitable spot near the sub's location. Sand away any paint at the contact point for the best connection. It is actually a good way to get a sound boost from your radio without having to give up the familiar controls. Getting them online can be a bit unreliable and expensive. Remember, if you want a question answered about a piece of gear, you must identify it by brand name and model number. Does your amp have high-level input? You may or may not know, but if u use a simple line converter, the higher you turn your stereo up, the more the head unit cuts the bass back in an attempt not to destroy your stock speakers.

Next

How do you hook up subwoofers to an stock radio?

how do i hook up subs to a stock radio

Avoid cable tiying the extension wire to solid things, as it will make removing your head unit difficult in future. Also the power,remote and ground wires from the sub,can I just piggy back these on the power,remote and ground terminals on the alpine amp? Most, but not all, subwoofers have these inputs; they get connected using speaker cables to the same speaker output jacks on your receiver or amplifier that are also hooked up to your speakers. And you can daisy-chain the remote turn-on wiring. Great connectors to use would be , so you won't have to crimp or solder wires together. If you want a question answered about your system, you must identify your equipment by brand names and model numbers. Seems you know your stuff maybe you can help me out with this problem? Or, you can run a second set of wires for the second powered sub.

Next

How do you add an amp to stock silverado stereo?

how do i hook up subs to a stock radio

My question is do I need to run a control cable back to the amp if so I am not sure where on the wiring kit to connect. Just your speakers to the amp. Step 3: Installing the Remote Wire Once you remove the stock stereo, you will see a blue and white wire, which is basically your remote wire. Stereo receivers, pre-amps, and integrated amplifiers rarely have subwoofer output jacks or offer bass-management options. List up any other good ideas or aftermarket items that would be helpful.

Next

How to hook up a subwoofer to a stereo system

how do i hook up subs to a stock radio

However, it is not a good idea to hook up subs directly to the stock radio. You need to pass the wire through the firewall. Audiocontrol does make one for subs that controls the bass roll off. Would it be better to buy a 4 channel amp, run the components from 2 channels, then use the line out from the other 2 channels to connect to the powered subs? We listen to music and play with car audio gear every day! This wire should be connected to the vehicle's chassis. Wiring So, now that you know you need to wire an amp to the radio and then the subs to the amp you may be wondering how do you do that.

Next

How do you add an amp to stock silverado stereo?

how do i hook up subs to a stock radio

Have a cup of tea while you warm up it was -2 Celsius all day when i did this! Then you have to find the output wires for the sound range that you need and connect them to the input of the amplifier. Try to use gentle curves with your wires and cables when possible to prevent unnecessary wear and tear. If you are running an amp on a stock stereo, there are other ways to turn the amp on without a remote wire, but that's the easiest way. Find a place to mount your sub Before you get started, find a suitable place in your vehicle to mount your sub. You haven't mentioned the remote turn-on lead - the powered sub won't turn on unless it's hooked up properly. Instead, you should wire an amp to the stock sound system and then wire the subs to the amp. It goes on the positive battery lead near the battery.

Next

How do you hook up subwoofers to an stock radio?

how do i hook up subs to a stock radio

There is only front and rear speaker input but the amp also supplies a woofer? Now, connect your amplifiers to their power source, check your wiring; then turn it on. Can I use one channel out for right input and the other channel for my left input? That's where I also first learned a little bit about sound mixers. Why can't I get my active box to work off of rca cables? You might be wondering can I hook up subs to my stock stereo? If you hooked your subs straight to the radio, then it would try to play all the sounds and that would not sound good. How a tweeter sounds should be a lot more important in your selection criteria than what its power rating is. It's usually blue, but confirm this with your owner's manual.

Next

How to hook up a subwoofer to a stereo system

how do i hook up subs to a stock radio

Any advice will be appreciated. I might be going about this the wrong way. If the amplifier is located away from the subwoofer, make sure that you run the wires under the carpeting of the car to keep it out of sight. That is because the wire is what carries the electronic single and if either the amp or sub receives poor signal, then the sound will be poor that you receive out of them. You also need to run power from the radio to the amp and then from the amp to the sub. An alternative method would be to run 8-gauge power wire with a 60-amp in-line fuse from the battery to a distribution block. Eventually, I moved to the writing team and spent a decade researching new products and getting even more hands-on with car audio gear.

Next

HOW TO: Install Subwoofer w/ Factory Radio

how do i hook up subs to a stock radio

You didn't mention what other gear is in your system, by it sounds to me that an amplifier with anywhere from 30 to 60 watts a channel would be plenty strong enough to drive tweeters. The one item that i am going to need is a connection from the stock stereo to the amp. If there's something about your system that doesn't sound right, you should take it up with your installer. Make sure that you carefully remove the screws that hold the stereo in place ensuring that no wires are cut. But if not, cut a short piece of the power cable, enough to cover the distance from the battery to the fuse holder location, and strip the insulation off both ends. Ive read reviews where people say this 2 wooofer sounds betyer than 2.

Next