You might just want to banish all traces of the decorating schemes of the 1970s, or need to add functionality or ease of cleaning. An internal plunger is used to stop water flow. The side that holds the drain opening determines what type of tub you need. If the tub drains slower, adjust the stopper lower. We partner with third party advertisers, who may use tracking technologies to collect information about your activity on sites and applications across devices, both on our sites and across the Internet. Lower the linkage so that the stopper sits lower into the drain. The cover plate simply screws into the body of the drain, as shown in , and can be removed or changed by just unscrewing it.Next
Regardless of the reason, replacing your bathtub drain yourself is much cheaper than hiring a contractor, and certainly more cost-effective than replacing the entire bathtub. Secure the flange on all three walls, as well as the sides of the tub. Use another piece of cardboard to protect the exposed porcelain side as well. Secure the flange to the studs by driving 1-inch galvanized roofing nails through the holes in the flange. If there is no access to the drain from behind or below, and your tub is sitting in its permanent spot, it is best to consult an expert to hook-up your drain. The tub can be removed whole as long as you have some help. Hold the drain ell in place with one hand.
Cut out a section of the cardboard to put inside the tub to help protect the surface while you work. Step 2 Remove the knob on the top of the stopper. With a screwdriver begin to slowly loosen and remove one of the screws, either one, your choice. Adjust set screws on the pipe holders and flanges to hold the new plumbing in place. If any of the pieces are too long for your application, cut them to size with a hacksaw. If the tub is fiberglass, drill holes at each stud. Dale Yalanovsky has been writing professionally since 1978.Next
Also anyone know why terry love isn't available on tapatalk? Tools needed: Screwdriver Plunger tub drains have a stopper located inside the waste and overflow pipe, and are activated using a Trip Lever or Turn Style overflow plate. You agree to these terms by using this website. If the outlet is threaded, screw the drain in place. If the set screw is removed and it will still not slide off the post, then there may be a calcium water build-up between the stopper and the post. Here are a few bathtub drain schematics and bathtub plumbing diagrams.Next
You will want to put a clean rag on the bottom of the tub beginning at the drain to cover the tub and keep the rocker arm from scratching your tub. The most difficult part of installing the tub itself is hooking up the bathtub drain to the rough plumbing. Nothing looks better than glistening water against a glistening hot tub shell. Step 2 You will need to remove the screws from the cover plate of the trip lever, however, remove only one screw from the faceplate at first. Wedge a piece of pipe underneath the new one to hold steady, then sweat the remaining joints. Carefully flip the tub on its side. Tighten the compression nuts coming from both the drain and overflow by hand from the access until you cannot turn them anymore.Next
Sometimes wiggling back and forth while pulling up may work as well. Insert the blade of a large screwdriver between the handles of the pliers and use it as a lever to tighten the drain flange. Lubricate the moving parts and the threads of the linkage, and reinstall into the overflow drain. If it's on the right, you need a right drain tub. Step 3 Either a screwdriver or allen wrench is needed to loosen the set screw.Next
Tighten the nut to hold in place. Check with your local sanitation or recycling company for details on disposing of your old tub. As soon as the faceplate is loose enough to swing down and away be careful not to scratch your tub to reveal the opposite side screw hole, reinstall the first screw back into the now exposed overflow elbow just a few turns. If you have this type of stopper you will know it when you start to pull it up and see the attached arm underneath. This might take you a couple of tries since the stopper will want to rotate with the pressure. This information is general and may not suit all applications.Next
It can also keep you from loosing the overflow washer that could fall down behind the tub. Content found on this site falls under the educational and entertainment category and is never intended to replace advice from legal, medical or financial professionals. Step 6 If needed, the stopper can be adjusted by either tightening or loosening the adjustable linkage that connects the trip lever to the stopper. Many have entire faceplates that rotate like on some bath wastes. Use a soft, dry cloth to ensure all moisture is out of the tub. Thanks for the good questions and quick response! If your stopper does not have a visible set screw on the knob then turn the stopper counter-clockwise until the stopper unthreads from the strainer and move on to Step 6. He specializes in do-it-yourself projects, household and auto maintenance and property management.Next